Goodyear Rubber Products





	Home About Us Location Maps Products Full PDF Catalogs Quote Contact Us

<< Previous Page

Click Here to open this page in a new window.

Next Page >>

THREAD  SEALING                                                                                                                               THREAD  SEALING
   COMPRESSION FITTINGS                                                                                                                    HOSE ENDS  AIR & HYDRAULIC
                                                                                                                                    PST® Band
                           PST® Coating  PST® Band  PST® Band
                                                                                                          1.   If necessary, spray adapter threads with Loctite® 7649TM Primer NTM.
                                                                                                               Allow to dry.
  1.   Slide fitting nut and ferrule back approximately 3/
                                                           4" from end of tubing.
                                                                                                          2.   Insert barbed hose stem into hose I.D. with slight twisting motion.
  2.   If necessary, spray the entire assembly with Loctite® 7649TM Primer NTM.
                                                                                                          3.   Install appropriate hose clamp.
       Allow to dry.
                                                                                                          4.   Apply a band of Loctite® PST® Thread Sealant to male hose stem threads
       Note:  Primer is not required for brass parts.
                                                                                                               upon installation or adding accessory device. Tighten snugly.
  3.   Apply a thin coating of Loctite® PST® Thread Sealant to tubing where
                                                                                                               Note:  Loctite® PST® Thread Sealant may attack synthetic rubber tubing.
       ferrule will be located.
  4.   Slide ferrule forward over Loctite® PST® Thread Sealant coated tubing,
                                                                                                           LOCTITE® BRAND THREAD SEALANT QUICK SELECTOR (TAPERED THREADS)
       then apply a thin bead of Loctite® PST® Thread Sealant coating to ferrule.
                                                                                                                                                       Instant    Max.     Steam    Temp.
  5.   Slide ferrule forward over Loctite® PST® Thread Sealant coated tubing.
                                                                                                           Application          Product       Primer    Seal    Pressure  Pressure  Range
  6.   Apply a small band of Loctite® PST® Thread Sealant to male threads.                                                     TM    ®              TM
                                                                                                          Stainless Steel  567  PST          Pimer N   500 psi  10,000 psi 235 psi -65°F to
  7.   Assemble and tighten normally.                                                                     and All Other    Thread Sealant                       (24 hours)         +400°F
                                                                                                          Metal Fittings
       Note:  Do not use on plastic fittings or tubing.
                                                                                                          Most Metal       565TM or 561TM      Primer NTM  500 psi 10,000 psi  n/a    -65°F to
                                                                                                          Fittings Except  PST® Pipe                            (24 hours)         +300°F
                                                                                                          Stainless Steel  Sealant
   FLARED/SWAGED FITTINGS                                                                                                      TM                   TM
                                                                                                          High Filtration/ 545  Thread       Primer N  500 psi  10,000 psi  n/a    -65°F to
                                                                                                          Zero ContaminationSealant                  (10 min.) (24 hours)         +300°F
                                       PST® Coating (For new or damaged flare or seat)
                                                                                                          Systems          Hydraulic/Pneumatic
                                                                                                          Stainless Steel  564TM Thread       Primer NTM  500 psi 10,000 psi  n/a    -65°F to
                                                                                                          and All Other    Sealant                              (24 hours)         +300°F
                                                                                                          Metal Fittings
                                                                                                          (lower strength)
                                                                                                                  DO NOT USE THESE PRODUCTS ON OXYGEN OR STRONG OXIDIZERS.
                                           PST® Band
                                                                                                           FLUID COMPATIBILITY
  1.   Disassemble and if necessary, spray all components with Loctite® 7649TM
                                                                                                          1.   Refer to Fluid Compatibility Chart  LT-836.
       Primer NTM. Allow to dry.
                                                                                                          2.   Contact your local Industrial Distributor.
  2.   Apply a thin coating of Loctite® PST® Thread Sealant to fitting face.
                                                                                                          3.   Call Henkel Technical Information. See back cover for the Henkel
  3.   Apply a band of Loctite® PST® Thread Sealant to male threads.
                                                                                                               Technical Information number in your area.
  4.   Assemble parts snugly.
10                                                                                                                                                                                         11