Page 139 - publication

stainless steel method
Introduction
Couplings
Outlets
Fittings
Val
ves &
Accesso
ries
HighPressure
Advanced CopperMethod (IPS)
DI-LOK
®
Nipples
Plain-EndFittings
HDPECouplings
Sock-It
®
Fittings
StainlessSteel Method
Roll
Groovers
Installation& Assembly
SpecialCoatings
DesignServices
Technical
Data
Master Format3 Part Specs.
PictorialIndex
CTS Copper
System
www.anvilintl.com 139
GRUVLOK STAINLESS STEEL FITTINGS
Anvil offers two different sets of stainless steel fttings. The Gruvlok Series Fittings have full fow designs formed from type
304SS pipe. The Schedule 10 fttings are fabricated from segmentally welded 316SS unless otherwise noted and are also available as
Schedule 40 and/or Type 304SS.
GRUVLOK COUPLING & FLANGE WORKING PRESSURE RATINGS (PSI)
ON 304 AND 316 STAINLESS STEEL ROLL GROOVED PIPE
Nominal
Pipe
Size
Pipe
O.D.
Nominal
Wall
Thickness
Pipe
Schedule
Number
Coupling and Flanges
Fig. 7000
Lightweight
Fig. 7001
Standard
Fig. 7003
Hingelok
Fig. 7004
HPR
Fig. 7010*
Reducing
Fig. 7012
Flange
Fig. 7013
Flange
Fig. 7400
Rigidlite
Fig. 7401
Rigidlok
Fig. 7400SS
Coupling
In./DN(mm) In./mm Inches – PSI
1
25
1.315
33.4
0.065 5S 400 400 – – – – – 300 – –
0.109 10S 400 500 – – – – – 300 – –
0.133 40 500 750 – – – – – 300 – –
11/ 4
32
1.660
42.4
0.065 5S 400 400 – – – – – 300 – 275
0.109 10S 500 500 – – – – – 300 – 300
0.140 40 500 750 – – – – – 300 – 300
11/ 2
40
1.900
48.3
0.065 5S 400 400 275 – – – – 300 400 275
0.109 10S 500 500 300 – – – – 300 500 300
0.145 40 500 750 300 – – – – 300 750 300
2
50
2.375
60.3
0.065 5S 250 325 250 325 250 250 275 250 325 275
0.109 10S 500 500 300 500 500 300 300 300 500 300
0.154 40 500 750 300 750 500 300 300 300 750 300
21/ 2
65
2.875
73.0
0.083 5S 250 325 250 325 250 250 275 250 325 200
0.120 10S 500 500 300 500 500 300 300 300 500 300
0.203 40 500 750 300 750 500 300 300 300 750 300
3
80
3.500
88.9
0.083 5S 250 325 250 325 250 250 275 250 325 200
0.120 10S 500 500 300 500 500 300 300 300 500 300
0.216 40 500 750 300 750 500 300 300 300 750 300
4
100
4.500
114.3
0.083 5S 200 250 200 250 200 200 250 200 250 200
0.120 10S 300 400 300 400 300 300 300 300 400 300
0.237 40 500 750 300 750 500 300 300 300 750 300
5
125
5.563
141.3
0.109 5S 125 200 125 200 125 125 200 125 200 –
0.134 10S 200 300 200 300 200 200 300 200 300 –
0.258 40 300 500 300 500 300 300 300 300 500 –
6
150
6.625
168.3
0.109 5S 75 125 75 125 75 75 125 75 125 125
0.134 10S 200 200 200 200 200 200 200 200 200 250
0.280 40 300 500 300 500 300 300 300 300 500 275
8
200
8.625
219.1
0.109 5S 50 75 50 75 50 50 75 50 75 75
0.148 10S 150 200 150 200 150 150 200 150 200 150
0.322 40 300 400 300 400 300 300 300 300 400 275
10
250
10.750
273.0
0.134 5S – 50 – 50 – 50 50 – 50 –
0.165 10S – 100 – 100 – 100 100 – 100 –
0.365 40 – 400 – 400 – 300 300 – 400 –
12
300
12.750
323.9
0.156 5S – 75 – 75 – 50 75 – 75 –
0.180 10S – 125 – 125 – 100 125 – 125 –
0.375 40 – 400 – 400 – 300 300 – 400 –
The following are pressure ratings for Gruvlok Stainless Steel
Piping Systems. The ratings for Schedule 10S pipe are based
upon the use of roll-groover roll sets that have been specifcally
designed for use on Schedule 10 Stainless Steel pipe. Using roll
sets that were designed for roll grooving standard wall pipe may
signifcantly reduce the pressure ratings that can be obtained.
The Model 1007/3007 roll groovers require the use of the
optional Schedule 10 roll set to groove Schedule 5S and 10S. For
grooving Schedule 40S on the Model 1007/3007 roll groovers,
the standard steel roll grooving set should be used.
GRUVLOK COUPLING & FLANGE WORKING PRESSURE RATINGS (PSI)
Notes: 1) Pressure ratings based on ASTM A312 Type 304 stainless steel pipe or equivalent.
2) Failure to use Rollers specifcally designed for Stainless Steel Pipe may signifcantly reduce pressure retention capabilities.
3) Pressure ratings on cut grooved pipe meet or exceed the schedule 40 pressure ratings listed above. For information regarding higher ratings contact Anvil.
4) * For pressure ratings on Figure 7010 Reducing Couplings use larger pipe size.
5) For pressure ratings for the reducing tees, concentric reducers and eccentric reducers, use the rating of the weakest end.
6) Pressure ratings on schedule 10 stainless steel pipe may be increased by using Anvil's 1007/3007 roll groovers with the schedule 10 roller set. Contact Anvil for details.
GL-2.10