Parker Hannifin Corporation
Tube Fittings Division
Columbus, Ohio
http://www.parker.com/tfd
R27
4300
Catalog
Equipment
Dimensions and pressures for reference only, subject to change.
Fig. R61 — Hydra-Tool
Fig. R62 — Electric Pump
Fig. R63 — Hand Pump
Fig. R64 — Flaring Cone
Fig. R65 — Die Ring
Hydra-Tool
Hydraulic Flaring and Pre-Setting Tool
Flaring
An efficient dependable device for 37° and 45° flaring of
steel, stainless steel and copper tube. This task is made easy
through hydraulic power provided by a hand or electric pump.
The equipment is portable and easy to use.
This tool accommodates dies for tubes ranging in inch sizes
from 4 through 32 (1/4” through 2” outside diameters) with
wall thicknesses as great as .134”, and metric sizes from 6mm
through50mm.Thehydraulic“push”of theHydra-Tool flares the
tube to a 37° flare angle. A gauge can be provided to enable
the operator to determine the pressure required to adequately
flare any given material and wall thickness of the tube. Com-
plete instructions are includedwith theHydra-Tool.See bulletin
4392-
B10. See the following for Hydra-Tool basic unit or kit,
and choice of power sources and necessary tooling.
NOTE
:
Flaring die sets and other tooling are available in non-
standard sizes upon request from the factory.
Se
e Appendix
for flaring pressures.
COMPONENTS REQUIRED
Part Name
Part No.
*
Hydra-Tool (basic unit)...............................................................
710400
B
*
Hydra-Tool Male Adapter...........................................................
6-8
F5OLO-S
*“
T” Adapter for Gauge................................................................
6
R6LO-S
*
Hose Assembly (for hand or electric pumps).............................
910004
*
Adapter for Gauge.....................................................................
6
G6L-S
*
Pressure Gauge (0 - 10,000 psi)...............................................
900044
Electric Hydraulic Pump (10,000 psi; 1/2 hp; 40-125 volt). .........
900085
Hand Hydraulic Pump (10,000 psi; 2 speed). .............................
900086
Die Ring (1/4” - 1 1/4”) (6mm - 32mm)........................................
710416
A
Die Ring (1 1/2” - 2”) (35mm - 50mm).........................................
710412
37
° Flaring Cone (1/4” - 1 1/4”) (6mm - 32mm). .........................
710419
37
° Flaring Cone (1 1/2” - 2”) (35mm - 50mm). ..........................
710411
Die Retainer Assembly (1/4” - 1 1/4”) (6mm - 32mm).................
710424-1
Die Retainer Assembly (1 1/2” - 2”) (35mm - 50mm)..................
710424-2
Flaring Die Sets.......................................................................... See
pages R28
–
R29
*
Lubricant....................................................................................
STP**
45
° Flaring Cone (1/4” - 1”).........................................................
910312
*
Included in Hydra-tool kit (Part 720370B-3)
**
STP Lubricant is the only lubricant recommended for use with Hydra-Tool.
Hydra-Tool Kit
Part Name
Part No.
Hydra-Tool Kit (for use with electric or hand pump)....................
720370
B-3
Includes basic unit, gauge adapter, Hydra-Tool connector,
lubricant, “T” adapter, carrying case, hose assembly,
operation manual and video.
Fig. R66 — Die Retainer
Flaring Tools
Fig. R67— Hydra-Tool Kit
link