4300
Catalog
Assembly / Installation
Parker Hannifin Corporation
Tube Fittings Division
Columbus, Ohio
http://www.parker.com/tfd
S14
Flanging Steps:
1.
Determine the extra cut-off length required for the
Parflange process by referring to Tables S9 and S10.
(
Each table is only a guide. Variations in tube wall thick-
ness and inconsistency in quality of tube cut-off may affect
actual dimensions. User should verify actual extra tube
cut-off length with one or two flanges prior to large scale
flanging.)
2.
Select the proper tooling for the tube size. The tube OD,
wall thickness and material must be known for proper
selection. Refer to
Table R6
on
page R24
for flanging capa-
bility by Parflange machine and availability of tooling
3.
With the sleeve properly positioned within the die set,
place the die set into the die holder of the machine.
4.
Insert the tube through the die opening until it comes in
contact with the tube stop. Do not forget to position the
tube nut over the tube in the proper orientation, especially
if the other tube end has already been flanged, or the tube
has sharp bends.
5.
Flange the tube as shown in Figure S17.
Note
:
For more information on Parflange procedures, ma-
chines, etc., Contact Parker Tube Fittings Division.
Fig. S18 – Extra cut-off length
Table S9 – Extra tube cut-off length guide for inch tube
Table S10 – Extra tube cut-off length guide for metric tube
Seal-Lok Assembly
Tube
O.D.
(
in.)
Tube Wall Thickness – Inch
.028 .035 .049 .065 .083 .095 .109 .120 .134 .156 .188
1/4 3/16 13/64 7/32
3/8
5/32 3/16 13/64 15/64 1/4
1/2
9/64 9/64 3/16 13/64 9/32 19/64 19/64
5/8
11/64 3/16 13/64 1/4 17/64 17/64
3/4
11/64 3/16 7/32 7/32 1/4 17/64 9/32
1
3/16 3/16 13/64 15/64 1/4 19/64
1 1/4
11/64 3/16 13/64 15/64 1/4 19/64 19/64 21/64
1 1/2
13/64 15/64 15/64 1/4 17/64 19/64 23/64 3/8
Tube
O.D.
(
in.)
Metric Tube Outside Diameter – (mm)
6
8
10
12
16
20
25
30
38
1.0
3/16
7/32
1/8
5/32
9/64
5.2
5.7
3.1
4.1
3.6
1.5
17/64
15/64
13/64
7/32
11/64
6.7
5.9
5.1
5.4
4.2
2.0
13/64
15/64
3/16
7/32
15/64
17/64
9/32
5.3
6.1
4.9
5.4
6.1
6.6
7.2
2.5
17/64
7/32
15/64
1/4
19/64
6.7
5.5
6.1
6.4
7.6
3.0
15/64
17/64
9/32
5/16
19/64
5.8
6.7
7.2
7.9
7.7
3.5
17/64
19/64
21/64
6.9
7.5
8.5
4.0
9/32
5/16
11/32
11/32
7.2
8.0
8.6
8.7
5.0
11/32
3/8
8.8
9.4
Dimensions and pressures for reference only, subject to change.