Goodyear Rubber Products
CALL
TOLL FREE
IN THE USA
1-866-711-4673
INTERNATIONAL SALES CALL
+1-727-342-5086
WE SHIP WORLDWIDE
International Sales Click Here
Get A
Quote
Now
Home
About Us
Product Brands
Catalogs
Contact Us
Locations
Corporate Headquarters,
Clearwater, Florida, (FL)
Parker Store, Bradenton, Florida, (FL)
Parker Store, St. Petersburg, (FL)
Parker Store, Ft. Myers, Florida, (FL)
Parker Store, Naples, Florida, (FL)
Parker Store, Tampa, Florida, (FL)
<< Previous Page
Click Here
to open this page in a new window.
Next Page >>
(Fleet)TruckPTFE &Technical&HydraulicThermoplasticAlphanumericHose,HoseAir&CoiledToolingApprovals& Products&Hose DesignPneumaticTubingFittingsIndexEquipmentAccessoriesGuides PMM-1 Portable Swage Instructions FittingsInformationFit.&HoseAccessories& I. Preparation of PMM-1 Portable Swaging Continue swaging stroke until bottom face of Machine pusher fully contacts top face of dies. Clean and lubricate Acme lead screw assembly. Retract pusher sufficiently to allow removal of Use lightweight lithium or molybdenum-based swaged coupling. grease. Measure swaged diameter of coupling and Clean and relubricate as required, particularly if inspect threads of male style couplings for any the tool has been exposed to dust or dirt indication of damage. On female swivel style during storage. couplings, inspect for free rotation and condition of nut. II. Versatile Features of PMM-1 Include IV. Swaging in Horizontal or Unsecured Position Three methods of mounting: bench, vise, or horizontal unsecured for ground or flat work Position torque reaction arm at 90� to the center surface. line of the machine. Swage die retaining clips for horizontal position. Following insertion of hose/coupling assembly into machines, it is necessary in this position to Thumbscrew for quick change of coupling secure the die halves with the spring retaining pushers. clips provided. Optional crank handle box end wrench part In the horizontal position, it is easier and number 821072. recommended to insert both die halves at the same time after the hose and coupling have III. Swaging in Vertical Bench Mounting Position been inserted. Install appropriate pusher, part number selected Each of the previously specified procedures from coupling style charts in 4660 Parflex also applies to use of the PMM-1 swager in this catalog fitting section. position. Clean and lubricate bore of swage dies with V. Vise Mounting Parker Hoze � Oil or other high film strength Oil. Repeat after two or three swages. Use Parker Secure PMM-1 swager in vise using only the lug 702 oil when swaging stainless steel couplings or ear provided. and lubricate each coupling. DO NOT ATTEMPT to vise mount by gripping the Install two-piece split die in bowl. Select proper round and tapered base of the machine. To do so die for specific coupling style and hose size from can result in serious injury. assembly tool selection chart in the 4660 cata- log. Using the vise lug, the machine may be mounted at an inclined angle or may be mounted After having properly inserted hose into coupling horizontally using the full area of the mounting and marking insertion depth, remove or elevate lug; this will be determined by the work area one die segment to allow installation of hose and arrangements. coupling. Note: When using the PMM-1 swager in the reaction Insert coupling all the way into pusher and exert arm position or the vise mounted position, an upward force; replace die segment in bowl of it will not be possible to maintain constant swager. Verify proper alignment with mating die rotation of the driving nut. It is recommended, half. however, that a continuous, smooth stroke be If lubrication has not previously been maintained whenever possible. accomplished, now is another opportunity to lubricate dies. Note: To avoid premature wear of dies, it is es- sential to distribute oil around the complete bore of dies. Using an appropriate wrench, begin clockwise rotation of hex drive nut. As skirt of coupling approaches the die opening, properly align entry of coupling by deflecting the hose as required continuing to exert an upward force on hose and coupling to keep it fully inserted in pusher. Note: The crank style box end wrench part num- ber 821072 is recommended as it eliminates slipping and provides easier nonstop rotation of drive nut. 250 Parker Hannifin Corporation Parflex Division Ravenna, Ohio
Goodyear Rubber Products
